Pages
Posts by category
- Category: Analysis
- Category: Concrete
- Flexural Strength of Concrete
- Effect of SCMs on Alkali-Silica Mitigation
- Reasons of Concrete Spalling
- Corrosion of Embedded Metals in Concrete
- Origin and Classification of Aggregates
- Pervious Concrete
- Characteristics of High volume Fly Ash Concrete
- Types of Chemical Admixtures
- Information for Ordering Concrete
- Carbonation and Corrosion
- Concrete Aggregates: Effects and Classification
- Rodded Unit Weight of Coarse Aggregates Test (ASTM C29)
- Concrete in Compression (ACI 318)
- Concrete in Tension: Tensile Strength of Concrete
- Compacting Factor Test
- Flow Table Test
- Cement Manufacturing Process
- Chloride Ingress into Concrete
- Gap-graded Aggregate
- Concrete Additives
- Recycled Concrete Aggregate
- Self-compacting Concrete: Fresh Properties
- How to Prepare Cube Samples from Fresh Concrete?
- Concrete Admixtures
- Reinforcement Steel and Prestressing Tendons
- Construction Process of RC Column
- Alkali–Aggregate Reactions
- Concrete Distress Identification
- Compaction Factor Test
- Shotcrete: Why to Use
- Effect of Age on Concrete Strength
- Water in Concrete
- Rebound Test: Equipment – Operation
- Classification of Aggregates
- Concrete Aggregates
- Visual Defects of Concrete
- Surface Rust Stains and Efflorescence
- Cracking and Honeycombing of Concrete
- Surface Scaling and Spalling of Concrete
- Production of Fly Ash
- Effect of Elevated Temperature on Concrete Strength
- Foamed Concrete
- What are Supplementary Cementing Materials (SCMs)
- Non-Destructive Testing of Concrete (NDT)
- Cement Setting and False Set
- Splitting Tensile Strength of Concrete
- Green Cements
- Portland Cement Hydration
- How Concrete is Made
- Freezing and Thawing Damage to Concrete
- Compressive Strength Test of Concrete
- Effect of Water-to-cement Ratio on Concrete
- Structural Damage Caused By Reinforcement Corrosion
- Corrosion Damage Stages During Service Life
- Permeability of Concrete
- What is Concrete Durability?
- Portland Cement: Compounds and Hydration
- Types of Concrete Admixtures
- How to Reduce Bleeding in Concrete?
- Workability of Concrete and the Factors Influencing its Value
- Geopolymer Concrete
- Mechanism of Chloride Induced Corrosion (Pitting Corrosion)
- Chemical Sulfate Attack on Concrete
- Fly Ash: Classification, Physical and Chemical Properties
- Modes of Concrete Deterioration
- ASTM: Types of Portland Cement
- Introduction to Concrete Components
- Category: Durability
- Category: Materials
- Category: Properties
- Category: Tests
- Category: Types
- Category: Construction
- Causes of Formwork Failures
- Formwork Materials
- How to Select the Construction Plant?
- Loads on Falsework and Formwork
- Lumber Formwork
- Desirable Properties of Plaster
- Portland Cement Plaster Materials
- Causes of Formwork Failures
- Types of Formwork
- Introduction to Construction
- Reinforced Concrete Quantity and Rate Analysis
- Objectives of a Building Code
- Calculation of Loads and Pressures on Concrete Formwork
- Category: Engineering Scholarships
- Category: Geotechnical
- Category: Management
- Category: Repair
- Category: Steel Design
- Category: Structural
- Category: Concrete Design
- Structural Design and Limit States
- Mechanisms of Concrete Confinement
- Shear Walls
- Flat Plate Floor System – Pros & Cons
- Practical Considerations for Reinforced Concrete Design
- 283 Structural Design Spreadsheets
- Deflection Control of R.C. Beams and Slabs
- Procedure of Structural Design
- RC Beam Behavior Under Load
- Reinforced Concrete as a Structural Material
- Type of Loads Acting on Structures
- Category: Earthquake
- Category: Concrete Design
- Category: Structures